#Potplayer best video quality settings install
#Potplayer best video quality settings Pc
#Potplayer best video quality settings download

Optimize for the following content, choose film and television for better effect, choose animation for better performance.īlack edge detection can be turned on, and the edge effect will be better, but it may accidentally hurt the subtitles. Checking this option will perform frame interpolation calculation (this frame interpolation is simply a mixture of two frames).Ĭreate a configuration scheme of SVP4MadVR with MadVR rendering.Īdd ffdshow raw video filter to the priority of personal filter, as the previous filter of madVR and mandatory use.Īt this point, the SVP4MadVR rendering scheme is configured, but SVP4 still needs to be configured. There is no need to check this item when using SVP frame interpolation. (Under normal circumstances, it is recommended to check) Remove stereo 3d, because 3d video is not played.ĭo not check enable smooth motion frame rate conversion. Remove only look at pixels in the frame center.Ĭhoose Jinc+AR or Super-xbr, as SVP4 is not used (expensive).Ĭhoose Cubic Bicubic60 to reduce consumption, as the case of using SVP4.Ĭheck delay playback start until queue is full. Here, I provide two configurations, one for the use of SVP4 and when not. So far, the MadVR rendering scheme is configured, but madVR still needs to be configured. In addition, if you do not use MadVR rendering and use EVR rendering, it is best to only check RGB32, RGB24, and RGB48 in Output Formats to get better results.Ĭreate a configuration scheme for MadVR rendering with core display hardware solution.Īdd madVR as the last filter in the personal filter priority and force it to use (Madshi renderer can also be used in video settings). The core display hard decoding only supports D3D11 and DXVA2, but using DXVA2 cannot select the device and conflicts with the independent display (calling the independent display fails), it is recommended The independent display supports the use of DXVA2 (native) or DXVA2 (copy back) for hard decoding. Here I use D3D11 to select the core display for hard decoding, because my independent display can’t hard decode the video. In order to watch movies smoothly, hard solutions must be used. Soft decoding consumes a lot of CPU, but the accuracy of soft decoding is higher than that of hard decoding. LAV Video Decoder setting is used to configure video decoding. Here, since the speakers used are stereo channels, check Enable Mixing. LAV Audio Decoder settings (do not check Convert Output to Standard Channel Layouts) LAV Splitter Source settings, (the default is fine)

But still need to configure LAVFilters.įor detailed settings of LAVFilters, see: (Not used in full-screen exclusive mode)Īt this point, the nuclear display hardware solution configuration is complete. Use the built-in OpenGL video renderer (10bit mode) or D3D11 video renderer (8bit mode) in the video settings. In the priority of personal filters, (add in order and set to mandatory use) The filter settings are as follows, (only check the built-in audio switcher) In the basic settings, check Save settings to INI file.Ĭreate a new configuration scheme for core display hardware solution.

Detailed configuration and instructions (you must run PotPlayer with a standalone display to get better performance)įirst configure PotPlayer+LAV+MadVR, as follows:.

#Potplayer best video quality settings install

Use SVP4, go to the official website to download, and then find the official website to install it (fee for Windows, free on Linux).

#Potplayer best video quality settings Pc

Use the compressed package of MadVR_v0.92.17 to install, the administrator runs install.bat, N card users also need to run enable nvidia 3d.reg, and then adjust the display range to 0-255 in the graphics control panel, or run madLevelsTweaker.exe to check Force PC level and Apply, close the program and restart. Use the compressed package of LAVFilters-0.74.1-圆4 to install, and the administrator can run install_audio.bat, install_splitter.bat, install_video.bat. Installation of LAVFilters, MadVR and SVP4.Install to the same directory as potplayer64. Intel H.264 MVC Decoder can be unchecked, generally used for 3D video.

#Potplayer best video quality settings download

If the installation interface of opencodec is not opened, please download and install it manually. OpenCodec is a codec for potplayer and it is recommended to install it.ĭetect H/W decoder/encoder is to automatically detect the hardware decoding encoder, no need to check it. This version is the last UI without major changes, and no useless functions such as live broadcast (local player). Here, it is recommended to use the historical version of potplayer64, because the function of the new version is a bit redundant,